Overview

Little Greene Intelligent Floor Paint is a durable, water-based paint designed for interior wood, concrete and primed metal floors. With a beautiful sheen of 30–40%, this quick-drying, low-odour formula is perfect for busy homes, drying within just four hours for minimal disruption.

Easy to wash, stain-resistant and built to withstand everyday wear, it delivers a hard wearing finish ideal for high traffic areas like stairs, hallways and landings. Certified child-safe and environmentally friendly, Intelligent Floor Paint combines performance, practicality, and Little Greene’s renowned depth of colour.

Available in all Little Greene colour range, Intelligent Floor Paint is a fantastic way to transform your space.

• Sheen level: 30–40%
• Durable, washable & easy to clean finish
• Low odour & Quick drying: touch dry in 1–2 hours
• Certified Child-Safe & environmentally friendly
• Available in all Little Greene colours

Tinted Colour Information

Preparation

Ensure the surface is clean, dry and free from dirt and grease.

Remove all imperfections and repair defects to achieve a smooth, sound surface.

New Wood:

• Soft Wood: Seal knots with Little Greene Aluminum Wood Primer to prevent staining. Then, apply 1 thinned coat of Little Greene Intelligent ASP to allow penetration into substrate, followed by the recommended 2 full coats of Intelligent Floor Paint.
• Resinous Hard Woods: Clean and treat with Little Greene Aluminum Wood Primer. Then, apply Little Greene Intelligent ASP, followed by the recommended 2 full coats of Intelligent Floor Paint.
• Ensure timber moisture is below 15%. Do not paint damp wood.
• Green oak must be weathered at least 6 months before painting.

Metals:

• Clean new metal (ferrous or non-ferrous) to remove rust.
• Then, apply Little Greene Intelligent ASP, followed by 2 coats of Intelligent Floor Paint.

Previously Painted Surfaces:

• Remove loose or flaking paint and degrease with a suitable detergent (e.g. sugar soap), then rinse with clean water.
• Sand with medium-grade paper to create a smooth, keyed surface, feathering edges where paint has been removed.
• Repair and sand as needed.
• Apply a thinned down coat to exposed surface as appropriate.

Concrete:

• Clean the surface thoroughly by brushing or vacuuming.
• For power-floated concrete, create a profile by vacuum blasting or using a proprietary acid etch before painting.
• Minor contamination, like oil spots, can be treated with a flame.
• Thin the first coat with approx. 15% (v/v) water to aid penetration, then apply two full coats.

Natural Stone:

• Porous stone can be prepared following the same method as concrete. Do not apply directly to non-porous granitic masonry.

This product is not recommended for painting laminate flooring or tiles.

Application

Always test a small area of the surface to be painted to ensure you are happy with the finished results

• Stir thoroughly before use.
• Lightly sand between coats to remove dust and imperfections for a smooth, professional finish.
• Do not apply below 8°C.

For brush application:

• Use a high-quality synthetic brush suited to the project. Condition new brushes by washing and drying with a lint-free cloth.
• Avoid dipping the brush too deep or overloading with paint.
• Apply in even strokes, maintaining a wet edge.
• Keep final strokes in one direction and avoid re-working once paint starts to dry to prevent lap marks.

For roller application:

• Use a short-nap wool blend sleeve for smooth surfaces; increase nap for textured areas.
• Maintain a wet edge and consistent stroke direction. Do not over-roll drying paint to prevent lap marks.
• Keep final strokes in one direction and avoid re-working once paint starts to dry to prevent lap marks.

For sprayer application:

• Conventional: Thin up to 40% (v/v) water. Tip: 1.60–2.00 mm (62–78 thou). Air pressure: 0.28–0.41 MPa (40–60 psi).
• Airless: Thin up to 20% (v/v) water. Tip: 0.28–0.54 mm (11–21 thou). Pressure: 12.6–19.6 MPa (1800–2800 psi).

Note: Adding an anti-slip aggregate is essential for safety-critical areas, such as external stairs, steps, and frequently wet floors. Use a dry, rounded aggregate with a particle size of 0.1–0.3 mm. The recommended dosage provides a moderate to heavy anti-slip texture. Little Greene LS30 Aluminium Oxide should be used.

Always follow manufacturer's instructions found on the packaging

Aftercare & Storage

Storage: Keep unused paint in a cool, dry, frost-free place away from sunlight. Replace lids securely after use. When unopened and stored correctly, the product remains stable for at least 2 years.

Cleaning: For light dirt, gently wipe with a damp sponge or lint-free cloth using a lukewarm solution of mild washing-up liquid. Repeat as needed. Remove DIY dust by vacuuming, using a soft brush attachment to avoid marking nearby surfaces. Make sure radiators are at room temperature before cleaning. Cleaning while hot can cause uneven or patchy polishing.

Care: Avoid placing heavy objects on painted surfaces for one week. Polishing floor cleaners should be avoided as this may produce a dangerous high slip surface.

Repair: Lightly rub down the area, apply suitable primer to any exposed surface, then repaint the whole section with one or two coats as needed. Please note that spot repairs may not match the original finish.